BUY Na Era

6G72

Mitsubishi · 6G72 3.0 V6

1990–2006

0 / 100
BUY

"Old, simple 3.0 V6 used in the Pajero IV and many earlier Mitsubishi and Chrysler cars. With good maintenance it often passes 400,000 km. Weak points are wear items: the timing belt and its hydraulic tensioner, hydraulic lifters that start to knock, and oil consumption from rings and valve-stem seals after about 100,000 km. Keep the oil level up to protect the narrow crank bearings."

Layout V6
Displacement 2972 cc
Power 178–220 hp
Type Petrol Na
Known Issues 5
Total Risk Cost €250–€0

Mileage Risk Timeline

When problems typically appear — enter your mileage to see your risk zone

km

Known Issues 5

▲ HIGH

Timing belt and hydraulic tensioner failure

N/A–N/A N/A–N/A
View details ▸
Detection

Sharp knock from the tensioner, flapping belt, oil on the timing cover; otherwise preventive only

Details

Belt-driven V6. The hydraulic tensioner often fails before the rest of the timing kit, letting the belt jump teeth, and an oil leak from the front-cover gasket can ruin the belt early. Chrysler gives a 60,000-mile (about 97,000 km, converted) belt interval. Sources disagree on damage: one says valves usually bend, a technical library says only the DOHC versions are interference engines. No reachable source gives a EUR cost.

Greece Note

Replace the belt, tensioner and front-cover seals together and keep the invoice.

▲ HIGH

Crankshaft bearing wear from oil starvation

N/A–N/A 250,000 km–300,000 km
View details ▸
Detection

Low oil pressure, knocking from the bottom end

Details

The crank bearings of the Mitsubishi petrol V6s are narrow and heavily loaded, and any oil starvation damages them; crank-bearing failures are described as not uncommon. Specialist media advise watching oil pressure closely at 250,000-300,000 km. No cost given.

Greece Note

Check the oil level often, especially on cars that burn oil.

● MODERATE

Oil consumption from worn piston rings and valve-stem seals

N/A–N/A 100,000 km–N/A
View details ▸
Detection

Blue smoke on cold start or after idling, oil level dropping between services

Details

The most common complaint on this V6. Specialist media report rising oil consumption from about 100,000 km and advise replacing the rings and valve-stem seals rather than topping up. Chrysler issued TSB 09-18-92 on oil consumption: pressed-in valve guides can work loose and the valve seals were revised in 1992; a clogged PCV drain also raises consumption. No EUR cost given.

Greece Note

No Greek-specific data found.

○ MINOR

Crankshaft pulley bolt can loosen (US recall)

N/A–N/A N/A–N/A
View details ▸
Detection

Noise from the front of the engine, loss of power steering assist

Details

NHTSA recall 00V311 (2000) covers 1992-1996 Montero and 1997-1999 Montero Sport with the 3.0L engine: the crankshaft pulley bolt can loosen and the pulley can fall off, causing loss of power steering assist. Dealers re-torque or replace the bolt free of charge.

Greece Note

US recall; European Pajero cars were not listed. Check the bolt torque at a belt change.

○ MINOR

Hydraulic lifter knock

€250–N/A 100,000 km–200,000 km
View details ▸
Detection

Ticking or knocking from the valve train, worst on a cold start

Details

The hydraulic lifters clog with deposits, especially with long oil-change intervals, and can knock by 100,000 km; they rarely last beyond 200,000 km. Replacing all of them costs about EUR 250 according to Kolesa.ru (upper cost not given).

Greece Note

Shorter oil-change intervals help.

Models with 6G72 2

Other Mitsubishi Engines

Tuning Potential

3000GT turbo: 350hp+ with ECU/boost

Frequently Asked Questions

Is the Mitsubishi 6G72 reliable?

The Mitsubishi 6G72 scores 80/100 with a verdict of BUY. It has 5 documented issues with total repair costs between €250 and €0.

What are the common problems with the 6G72?

The most common issues are:

  • Timing belt and hydraulic tensioner failure — high, repair cost N/A–N/A, N/A–N/A
  • Crankshaft bearing wear from oil starvation — high, repair cost N/A–N/A, 250,000 km–300,000 km
  • Oil consumption from worn piston rings and valve-stem seals — moderate, repair cost N/A–N/A, 100,000 km–N/A
  • Crankshaft pulley bolt can loosen (US recall) — minor, repair cost N/A–N/A, N/A–N/A
  • Hydraulic lifter knock — minor, repair cost €250–N/A, 100,000 km–200,000 km
What cars use the Mitsubishi 6G72?

The 6G72 is found in:

How much does it cost to repair the 6G72?

Total potential repair costs for all 5 known issues range from €250 to €0.

What years was the 6G72 produced?

The Mitsubishi 6G72 was produced from 1990 to 2006. It is a 2972cc V6 petrol na engine.

Scores are calculated from documented issues, repair costs, and failure patterns across thousands of owner reports and technical sources. Learn about our methodology. Always inspect before you buy.