Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA)
Ford · Duratec V6 2.5 / 3.0 (Mondeo Mk3, ST220)
2000–2007
"Ford's all-alloy Duratec V6 in the Mondeo Mk3: 2.5 (170 hp) and 3.0 (ST220, 226 hp), with timing chains. Smooth and long-lived when the oil is changed on time - one Mondeo V6 reached 291,000 miles - but it does not forgive low or old oil: worn chain tensioners and bottom-end failures have finished many neglected ST220s. Expect oil leaks (rear crankshaft seal, cam covers, sump), sticking intake runner flaps (IMRC), a fuel pump that fails around 100,000 miles (tank out) and ageing cooling parts. Listen for chain rattle and bottom-end knocks before buying."
Mileage Risk Timeline
When problems typically appear — enter your mileage to see your risk zone
Known Issues 6
Engine failure after oil neglect (chain tensioners, bearings)
▸Chain rattle, knocking from the bottom of the engine, oil pressure warning
A British buying guide says terminal engine failure has killed many ST220s: a rattling chain often signals the end of the engine and bottom-end knocks are not worth the risk. Another reports a main bearing failure at 60,000 miles (about 97,000 km, converted) despite twice-yearly oil changes, warns against running the engine low on oil and advises light synthetic oil for the narrow oilways. Engine databases add that poor oil shortens the life of the hydraulic chain tensioners and lifters. A reconditioned engine fitted cost about GBP 1,600 (approx. EUR 1,870, converted) in 2019.
Change the oil on time with light synthetic oil and check the level often. No Greek-specific data found.
Cooling system leaks and overheating (water pump, radiator, expansion tank)
▸Coolant loss, overheating, white residue around hoses and the expansion tank
Engine databases say a worn water pump or clogged radiators are the main causes of overheating on the 2.5 and 3.0; British guides report cracking expansion tanks and radiators and warn that coolant leaks can be catastrophic in the cramped engine bay. No source gives a price.
Greek summer heat stresses old cooling parts; check hoses and the expansion tank before summer. No Greek-specific data found.
Oil leaks (rear crankshaft seal, cam covers, sump)
▸Oil from the gearbox bellhousing drain hole, oily cam covers or sump, burning oil smell
Small oil leaks are common: sump gaskets, rear crankshaft seals, rear cam cover seals and oil filters can all weep. A rear crankshaft seal costs little but takes about six hours, and with the clutch slave cylinder done at the same time it becomes a four-figure (GBP) bill; a leaking seal can ruin the clutch. An engine database blames a contaminated crankcase ventilation for seal leaks.
No Greek-specific data found.
Fuel pump and tank strainer failure (tank must come out)
▸Hard starting, rough running at high revs, lean-mixture engine light
The in-tank strainer clogs with dirt by 80,000-100,000 km, and the pump itself commonly fails at about 100,000 miles (about 161,000 km, converted); the tank has to be dropped to replace it. A Russian guide advises replacing the pump rather than only cleaning the strainer. Engine databases link poor fuel to filter, pump and pressure-regulator failures. No source gives a price.
Buy fuel from busy stations; poor fuel shortens the pump's life. No Greek-specific data found.
Intake runner flaps (IMRC) stick
▸Engine light, flat spot or loss of power at higher revs, IMRC fault codes
A German used-car guide names the intake manifold runner control (IMRC) as the typical weak point of the 2.5, 3.0 and ST220 V6; an engine database lists a jammed flap in the intake manifold on the 2.5. Otherwise the guide sees little cause for concern with the V6. No source gives a repair price.
No Greek-specific data found.
Spark plugs and coils (misfires)
▸Misfire, rough running, flashing engine light
A Russian guide says the plugs rarely last 30,000 km and usually need replacing at 15,000-20,000 km on poor fuel; an engine database says poor fuel damages plugs and coils. The rear three plugs require removing the intake manifold. Misfires can also come from the airflow meter or vacuum hoses. No source gives a price.
No Greek-specific data found.
Models with Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) 2
Related Guides
Other Ford Engines
Sigma 1.4
Sigma 1.4 16V (Zetec-SE / Duratec)
View details → Compare: Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) vs Sigma 1.4Sigma 1.25
Sigma 1.25 (FUJA/SNJA/STJA)
View details → Compare: Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) vs Sigma 1.251.8 TDDi / DI (Endura-DI)
Endura-DI 1.8 TDDi (rotary pump)
View details → Compare: Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) vs 1.8 TDDi / DI (Endura-DI)Dragon 1.5 I3 (EcoBoost / Ti-VCT)
1.5L Dragon I3 (turbo and non-turbo)
View details → Compare: Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) vs Dragon 1.5 I3 (EcoBoost / Ti-VCT)Tuning Potential
Limited aftermarket
Frequently Asked Questions
Is the Ford Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) reliable?
The Ford Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) scores 79/100 with a verdict of BUY. It has 6 documented issues with total repair costs between €1,870 and €0.
What are the common problems with the Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA)?
The most common issues are:
- Engine failure after oil neglect (chain tensioners, bearings) — high, repair cost €1,870–N/A, 97,000 km–N/A
- Cooling system leaks and overheating (water pump, radiator, expansion tank) — moderate, repair cost N/A–N/A, N/A–N/A
- Oil leaks (rear crankshaft seal, cam covers, sump) — moderate, repair cost N/A–N/A, N/A–N/A
- Fuel pump and tank strainer failure (tank must come out) — moderate, repair cost N/A–N/A, 80,000 km–161,000 km
- Intake runner flaps (IMRC) stick — moderate, repair cost N/A–N/A, N/A–N/A
What cars use the Ford Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA)?
How much does it cost to repair the Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA)?
Total potential repair costs for all 6 known issues range from €1,870 to €0.
What years was the Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) produced?
The Ford Duratec V6 2.5 / 3.0 (LCBD, REBA, MEBA) was produced from 2000 to 2007. It is a 2967cc V6 petrol na engine.
Scores are calculated from documented issues, repair costs, and failure patterns across thousands of owner reports and technical sources. Learn about our methodology. Always inspect before you buy.