N12/N16 · EP6 VTi (Prince NA)
MINI · 1.6L I4
2006–2018
"Naturally aspirated, port-injected Prince (MINI Cooper N12/N16, Peugeot/Citroen 1.6 VTi 120). No turbo, no high-pressure pump and no valve coking, and far fewer chain failures than the THP - but it is known for burning oil, and cooling-system leaks are common. Check the oil level before you buy."
Mileage Risk Timeline
When problems typically appear — enter your mileage to see your risk zone
Known Issues 4
High oil consumption - piston rings and valve stem seals
▸Oil level drops between services, blue smoke, oily spark plugs, low-oil warning
The dominant fault of the port-injected Prince: 173 of 533 owner reviews on fiches-auto mention oil consumption or leaks, mostly on engines built before 2010. Coked rings and hardened stem seals let oil into the cylinders; worn bores can end in a block replacement.
Check the dipstick every fuel stop. A VTi or Cooper that needs a litre every 1,000-2,000 km is a negotiating point or a walk-away.
Valve and cylinder-head damage after misfires
▸Persistent misfire, loss of compression on one cylinder, rough idle
Polish and French specialist media report valve and cylinder-head work on the 1.6 VTi after misfires, sometimes ending in an engine replacement.
Do not drive on with a flashing engine light - have the misfire found first.
Water pump, thermostat housing and coolant leaks
▸Fluctuating temperature gauge, slow coolant loss, residue around the plastic thermostat housing
Cooling faults are the second most common complaint on the VTi (52 cooling and 40 water-pump reports in 533 reviews). Pump, thermostat and coolant cost about 480-680 EUR.
Greek summer heat ages the plastic housing faster - inspect it at every service.
Timing chain stretch and tensioner wear
▸Rattle on cold start, camshaft correlation codes
Same chain and hydraulic tensioner design as the turbo engines but far less stressed: only 19 of 533 VTi owner reviews mention the timing drive, against 100 of 357 on the THP 156. Owners report chain work at 75,000-80,000 km. A chain kit for a MINI Cooper N12 costs about 1,400-1,800 EUR in Germany.
Cold-start the car before buying. Low oil makes the tensioner rattle.
Models with N12/N16 · EP6 VTi (Prince NA) 22
Other MINI Engines
Tuning Potential
Limited
Frequently Asked Questions
Is the MINI N12/N16 · EP6 VTi (Prince NA) reliable?
The MINI N12/N16 · EP6 VTi (Prince NA) scores 70/100 with a verdict of ACCEPTABLE. It has 4 documented issues with total repair costs between €1,880 and €2,480.
What are the common problems with the N12/N16 · EP6 VTi (Prince NA)?
The most common issues are:
- High oil consumption - piston rings and valve stem seals — high, repair cost N/A–N/A, N/A–N/A
- Valve and cylinder-head damage after misfires — moderate, repair cost N/A–N/A, N/A–N/A
- Water pump, thermostat housing and coolant leaks — moderate, repair cost €480–€680, N/A–N/A
- Timing chain stretch and tensioner wear — moderate, repair cost €1,400–€1,800, 75,000 km–N/A
What cars use the MINI N12/N16 · EP6 VTi (Prince NA)?
How much does it cost to repair the N12/N16 · EP6 VTi (Prince NA)?
Total potential repair costs for all 4 known issues range from €1,880 to €2,480. The most expensive issue is typically Timing chain stretch and tensioner wear.
What years was the N12/N16 · EP6 VTi (Prince NA) produced?
The MINI N12/N16 · EP6 VTi (Prince NA) was produced from 2006 to 2018. It is a 1598cc I4 petrol na engine.
Scores are calculated from documented issues, repair costs, and failure patterns across thousands of owner reports and technical sources. Learn about our methodology. Always inspect before you buy.