4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA)
Audi · 4.2L NA V8
2005–2015
"Direct-injection 4.2 V8 of the RS4 B7, R8, RS5, Q7, A6 C6 and A8 D3. Sweet and high-revving, generally robust. Carbon builds on the intake valves, and the rear-mounted timing chain is an engine-out job if its guides wear - reports conflict on how often that happens on the FSI. Not the 40-valve S4 B6/B7 engine."
Mileage Risk Timeline
When problems typically appear — enter your mileage to see your risk zone
Known Issues 2
Rear timing-chain guides and tensioners wear (engine-out job)
▸Rattle from the back of the engine on cold start, camshaft-crankshaft correlation fault codes
The FSI drives its cams by chains from the flywheel side, so any guide or tensioner job means removing the engine. Sources conflict: one buyer guide rates RS4 guide wear as critical and a German guide says all big Audi V6/V8/V10 chains eventually need work, while a UK specialist says the RS4 uses steel guides and is not a problem. Chain service quoted at USD 1,500-3,500 (converted ~1,380-3,220 EUR); engine-out labour can push it higher.
Stick to short oil-change intervals with the specified 0W40/5W40 oil. No Greek-specific data found.
Intake-valve carbon build-up and blue smoke (direct injection)
▸Gradual power loss, rough running, blue smoke after low-rev driving, check-engine light in bad cases
Direct injection means no fuel washes the intake valves, and low-rev use lets oil collect in the inlet. Cleaning needs the top half of the engine stripped; chemical cleaners are less effective. Coil packs also fail on some cars and a misfire can damage a catalyst. No source gives a price or mileage.
City-only use in Athens traffic is the worst case; regular high-rev runs help. No Greek-specific data found.
Models with 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) 7
Related Guides
Other Audi Engines
2.5 TFSI I5 (EA855: CEPA, CZGA/CZGB, DAZA, DNWA)
2.5L Turbo I5
View details → Compare: 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) vs 2.5 TFSI I5 (EA855: CEPA, CZGA/CZGB, DAZA, DNWA)4.0 TDI V8 EA898
4.0 TDI V8 EA898 (CZAC/DCZF) SQ7/SQ8
View details → Compare: 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) vs 4.0 TDI V8 EA8985.2 FSI V10 Gen 2 (dual injection)
5.2 FSI V10 NA Gen 2 (R8 Type 4S, CSPA/CSPB)
View details → Compare: 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) vs 5.2 FSI V10 Gen 2 (dual injection)EA837 3.0 TFSI supercharged
3.0L TFSI Supercharged V6
View details → Compare: 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) vs EA837 3.0 TFSI superchargedTuning Potential
N/A — already high power
Frequently Asked Questions
Is the Audi 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) reliable?
The Audi 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) scores 76/100 with a verdict of ACCEPTABLE. It has 2 documented issues with total repair costs between €1,380 and €3,220.
What are the common problems with the 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA)?
The most common issues are:
- Rear timing-chain guides and tensioners wear (engine-out job) — high, repair cost €1,380–€3,220, N/A–N/A
- Intake-valve carbon build-up and blue smoke (direct injection) — moderate, repair cost N/A–N/A, N/A–N/A
What cars use the Audi 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA)?
How much does it cost to repair the 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA)?
Total potential repair costs for all 2 known issues range from €1,380 to €3,220. The most expensive issue is typically Rear timing-chain guides and tensioners wear (engine-out job).
What years was the 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) produced?
The Audi 4.2 V8 FSI (BAR/BVJ/BNS/BYH/CAU/CFSA) was produced from 2005 to 2015. It is a 4163cc V8 petrol na engine.
Scores are calculated from documented issues, repair costs, and failure patterns across thousands of owner reports and technical sources. Learn about our methodology. Always inspect before you buy.